--- title: Animal microchips slug: zero/rfid/animal-microchips description: Learn how to locate and read animal microchips as well as find information about the animal in online pet recovery services image: https://archbee-image-uploads.s3.amazonaws.com/3StCFqarJkJQZV-7N79yY/pgGJTXctU9J_hNMv0HX0J_animalchips001.png docTags: createdAt: 2022-11-11T12:11:31.000Z --- ![](https://api.archbee.com/api/optimize/3GUDYkC5JgUWgo6RW8piO-cNuTTC7kZqBSygHBzPVHa-20241024-181739.png) A [microchip](https://en.wikipedia.org/wiki/Microchip_implant_\(animal\)) is a radio-frequency identification (RFID) [transponder](https://en.wikipedia.org/wiki/Transponder) that stores a unique identification number and is roughly the size of a grain of rice. The microchip is implanted under the animal’s skin. When scanned with a reader, the microchip transmits its ID number. This ID number can help you find information about the animal and its owner if added to a database. Flipper Zero allows you to read animal microchips thanks to its low-frequency RFID antenna. The Flipper Zero antenna was designed to operate at 125 kHz, while most animal microchips operate at 134.2 kHz. Support for reading 134.2 kHz microchips was implemented as an additional feature. To read a microchip, hold your Flipper Zero over the animal's microchip for 3 seconds. Otherwise, Flipper Zero won’t detect it. On this page, you’ll learn how to locate and read animal microchips. You’ll also learn how to find information about the animal in online pet recovery services. *** # Animal RFID microchips supported by Flipper Zero - **Compatible microchips:** [FDX-B](https://www.priority1design.com.au/fdx-b_animal_identification_protocol.html) (15-digit, ISO-compliant, including thermo microchips), FDX-A (10-digit, not ISO-compliant), and other chips supported by Flipper Zero in the form factor of an animal microchip. - **Reading frequency:** 125 kHz. Flipper Zero can also read microchips in the 110-140 kHz range but with a shorter reading distance. - **Reading distance:** 10 mm (0.39 inch). *** # Reading animal microchips Animal microchips can be located at [different sites](https://wsava.org/wp-content/uploads/2020/01/Veterinary-List-of-Recommended-Microchip-Implantation-Sites.pdf). In dogs and cats, one microchip is usually inserted under the skin at the back of the neck **between the shoulder blades** on the dorsal midline. Continental European pets get a microchip **in the midway region of the left neck**. ![](https://api.archbee.com/api/optimize/3GUDYkC5JgUWgo6RW8piO-yWQb-M5UMODNBjGPfDOJd-20241024-181823.png) ## Method 1. Locating the microchip with your fingers We recommend to first locate the animal microchip with your fingers and then read it with your Flipper Zero. Move your fingertips over the pet’s skin between the shoulder blades and the midway region of the left neck. Apply gentle pressure to see if you can detect a solid rice-grain-sized object just under the skin. Mind that animal microchips might migrate slightly from the original location. Once you’ve located the microchip, scan it with your Flipper Zero using the ASK coding: ::::WorkflowBlock :::WorkflowBlockItem Go to **Main Menu -> 125 kHz RFID -> Extra Actions**. ::: :::WorkflowBlockItem Select **Read ASK** and press %ok%**OK**. ::: :::WorkflowBlockItem Hold your Flipper Zero as close as possible to the microchip, and don’t move the device for three seconds. ![](https://api.archbee.com/api/optimize/3GUDYkC5JgUWgo6RW8piO-BTwhIvFlP8EllkhJGx7ZW-20241107-102807.png "Hold your Flipper Zero so that the microchip is in the center of the device’s back") ::: :::: ## Method 2. Locating the microchip with your Flipper Zero To locate and read the animal microchip, you need to position your Flipper Zero precisely atop the microchip as close as possible and wait for three seconds. To increase the chance of detecting the animal microchip, we recommend reading in ASK coding mode: ::::WorkflowBlock :::WorkflowBlockItem Go to **Main Menu -> 125 kHz RFID -> Extra Action**. ::: :::WorkflowBlockItem Select **Read ASK** and press %ok%**OK**. ::: :::WorkflowBlockItem Move your Flipper Zero as close as possible to the pet’s skin (the device’s back facing the animal’s skin) and move the device step by step, holding it for 3 seconds at each location. ![](https://api.archbee.com/api/optimize/3GUDYkC5JgUWgo6RW8piO-uDjsDej3RICnWIbDj9_0h-20241107-102819.png "It is important to keep your Flipper Zero still for 3 seconds at every stop") Move your Flipper Zero in the pattern shown below until the microchip is detected. ![](https://api.archbee.com/api/optimize/3GUDYkC5JgUWgo6RW8piO-iIjHejI9KHa_nUcudwSbP-20241024-182334.png) Pay attention to the LED on your Flipper Zero: ![](https://api.archbee.com/api/optimize/3StCFqarJkJQZV-7N79yY/n2vGgEFstHBS0K4TuI6Qt_monosnap-miro-2023-08-04-13-44-38.jpg "LED indication will help you to locate the microchip") If the microchip wasn’t detected, rotate your Flipper Zero 90° and repeat the scanning procedure as shown below. ![](https://api.archbee.com/api/optimize/3GUDYkC5JgUWgo6RW8piO-HLzzshH8LDvCtSShpqVMg-20241024-182359.png) ::: :::: ## If your Flipper Zero doesn’t detect the microchip - The microchip may be out of range. -> Try to move your Flipper Zero in the patterns shown above with smaller steps and hold the device at each stop a bit longer. - The microchip might have migrated from the original location. -> Try to cover a larger area with your Flipper Zero. - Metal objects or electronic equipment may interfere with the microchip reading. -> Try to scan the animal away from these objects. - The animal might have a high-frequency RFID microchip. -> Try to scan it [using the NFC application](https://docs.flipper.net/zero/nfc/read). - The animal might have an unsupported type of microchip. -> Contact your local veterinary clinic to scan the animal with their equipment. *** # Animal RFID microchip data structure After you capture the microchip data, Flipper Zero will display the information about the animal: microchip type, ID number, microchip data, and animal’s temperature (if the microchip can measure it). ![](https://api.archbee.com/api/optimize/3StCFqarJkJQZV-7N79yY/meOm-VShGcnWAUDS4sepx_monosnap-miro-2023-08-04-13-44-59.jpg "Data structure of an ISO-compliant FDX-B microchip") ISO-compliant animal microchips have 15-digit ID numbers. The first three digits represent an [ISO 3166-1 numeric](https://en.wikipedia.org/wiki/ISO_3166-1_numeric) country code or a [manufacturer code](https://cdn.flipperzero.one/manufacturersisosandcountrycodes.pdf). The remaining 12 digits represent the unique microchip number. :::Iframe{iframeHeight="500" code="
Always use diagnostic thermometers for accurate temperature measurements
Flipper Zero can read the temperature measured by microchips. Even though it’s a non-invasive way of frequently measuring a pet’s temperature, microchip temperature isn’t a replacement for a certified thermometer.
"} ::: *** # Search for microchip ID info in animal databases Once you know the animal ID number, you can find the information about the animal in pet recovery services by entering the ID number: ::::LinkArray{contentSource="CUSTOM"} :::LinkArrayItem{headerType="IMAGE" headerImage="https://api.archbee.com/api/optimize/3StCFqarJkJQZV-7N79yY/5ReTYIMgKzRCpzFe1_cHa_monosnap-miro-2022-11-29-18-09-21.png"} ****[American Animal Hospital Association](https://www.aaha.org/petmicrochiplookup)**** United States and Canada ::: :::LinkArrayItem{headerType="IMAGE" headerImage="https://api.archbee.com/api/optimize/3StCFqarJkJQZV-7N79yY/M4rciVfruKP12IPqsbrHx_monosnap-miro-2022-11-29-18-09-04.png"} [Europetnet](https://www.europetnet.com/) Europe ::: :::LinkArrayItem{headerType="IMAGE" headerImage="https://api.archbee.com/api/optimize/3StCFqarJkJQZV-7N79yY/IbrkJTnzGy1zW26kwjPpz_monosnap-miro-2022-11-29-18-09-35.png"} [PETMAXX](http://www.petmaxx.com/) Worldwide ::: :::: If you didn’t find information about the animal in the services above, try using your local pet recovery service.